Adinath Electronics

Digital Signal Processors & Controllers - DSP, DSC 16 Bit MCU/DSP 30M 48KB FL
 • High-current sink/source I/O pins: 25 mA/25 mA• Timer module with programmable prescaler:- Five 16-bit timers/counters; optionally pair16-bit timers into 32-bit timer modules• 16-bit Capture input functions• 16-bit Compare/PWM output functions• 3-wire SPI modules (supports 4 Frame modes)• I 2C™ module supports Multi-Master/Slave modeand 7-bit/10-bit addressing• Two UART modules with FIFO Buffers• CAN module, 2.0B complian

8-bit Microcontrollers - MCU 8-bit MCU Value Line 16 MHz 8kb FL 128EE
We have the entire STM8S003F3 series available price
STM8S003F3P6TR 
STM8S003F3U6TR
STM8S003F3P6

An 8-bit low-power, high-performance CMOS microcontroller, the AT89C55WD-24PU has 256 bytes of RAM and 20kB of flash programmable read-only memory. The 80C51 and 80C52 industry standard instruction set and pinout are compatible with the device, which is made utilising high-density non-volatile memory technology. A traditional non-volatile memory programmer may be used to user-code the programme memory thanks to the on-chip Flash. A powerful microcomputer, the AT89C55WD combines a modular 8-bit CPU with flash on a monolithic chip to give a highly adaptable and affordable solution to many embedded control applications. The following features are included as standard with the AT89C55WD. 20kB of Flash, 256 RAM bytes, 32 I/O lines, three 16-bit timer/counters, a full-duplex serial port, a six-vector, two-level interrupt architecture, and on-chip oscillator and clock circuits are all included.

C8051F350/1/2/3 devices are fully integrated mixed-signal System-on-a-Chip MCUs. Highlighted features are listed below. 
• High-speed pipelined 8051-compatible microcontroller core (up to 50 MIPS)
• In-system, full-speed, non-intrusive debug interface (on-chip)
• 24 or 16-bit single-ended/differential ADC with analog multiplexer • Two 8-bit Current Output DACs
• Precision programmable 24.5 MHz internal oscillator
• 8 kB of on-chip Flash memory
• 768 bytes of on-chip RAM
• SMBus/I2C, Enhanced UART, and SPI serial interfaces implemented in hardware
• Four general-purpose 16-bit timers
• Programmable counter/timer array (PCA) with three capture/compare modules and watchdog timer function
• On-chip power-on reset, VDD monitor, and temperature sensor
• On-chip voltage comparator
• 17 Port I/O (5 V tolerant)

The C8051F12x and C8051F13x device families are fully integrated mixed-signal System-on-a-Chip MCUs with 64 digital I/O pins (100-pin TQFP) or 32 digital I/O pins (64-pin TQFP). Highlighted features are listed below. 
• High-Speed pipelined 8051-compatible CIP-51 microcontroller core (100 MIPS or 50 MIPS)
• In-system, full-speed, non-intrusive debug interface (on-chip)
• True 12 or 10-bit 100 ksps ADC with PGA and 8-channel analog multiplexer
• True 8-bit 500 ksps ADC with PGA and 8-channel analog multiplexer (C8051F12x Family)
• Two 12-bit DACs with programmable update scheduling (C8051F12x Family)
• 2-cycle 16 by 16 Multiply and Accumulate Engine (C8051F120/1/2/3 and C8051F130/1/2/3)
• 128 or 64 kB of in-system programmable Flash memory
• 8448 (8 k + 256) bytes of on-chip RAM
• External Data Memory Interface with 64 kB address space
• SPI, SMBus/I2C, and (2) UART serial interfaces implemented in hardware
• Five general purpose 16-bit Timers
•Programmable Counter/Timer Array with 6 capture/compare modules
• On-chip Watchdog Timer, VDD Monitor, and Temperature Sensor

The C8051F020/1/2/3 devices are fully integrated mixed-signal System-on-a-Chip MCUs with 64 digital I/O pins (C8051F020/2) or 32 digital I/O pins (C8051F021/3). Highlighted features are listed below; 
 • High-Speed pipelined 8051-compatible CIP-51 microcontroller core (up to 25 MIPS)
• In-system, full-speed, non-intrusive debug interface (on-chip)
• True 12-bit (C8051F020/1) or 10-bit (C8051F022/3) 100 ksps 8-channel ADC with PGA and analog multiplexer
• True 8-bit ADC 500 ksps 8-channel ADC with PGA and analog multiplexer • Two 12-bit DACs with programmable update scheduling • 64k bytes of in-system programmable FLASH memory • 4352 (4096 + 256) bytes of on-chip RAM
• External Data Memory Interface with 64k byte address space
• SPI, SMBus/I2 C, and (2) UART serial interfaces implemented in hardware
• Five general purpose 16-bit Timers
• Programmable Counter/Timer Array with five capture/compare modules
• On-chip Watchdog Timer, VDD Monitor, and Temperature Sensor

Low-cost members of the ST62xx 8-bit HCMOS family of microcontrollers designed for low to medium complexity applications include the ST6215C and 25C devices. Every ST62xx device is built using a building block methodology, with several on-chip peripherals around a common core.The ST62E25C is the erasable EPROM version of the ST62T15C, T25C devices. It may be utilised in the development stage for both the corresponding ST6215C, 25C ROM devices and the ST62T15C, T25C target devices.

The STM32G030F6P6 is a compact, low-cost 32-bit microcontroller from STMicroelectronics, belonging to the STM32G0 series. It is built around the Arm® Cortex®-M0+ core, operating at frequencies of up to 64 MHz, and is optimized for applications that require efficient performance, low power consumption, and minimal board space.

This device features 32 KB of Flash memory and 8 KB of SRAM, providing sufficient resources for small to medium embedded applications. It operates within a supply voltage range of 1.7 V to 3.6 V, making it suitable for battery-powered and low-voltage systems. Multiple low-power modes, including Sleep and Stop, help reduce energy consumption during idle periods, extending battery life in portable designs.

The STM32G030F6P6 integrates a practical set of peripherals for general-purpose control tasks. It includes a 12-bit ADC with several input channels for analog measurements, as well as general-purpose timers capable of PWM generation, input capture, and timing functions. Communication peripherals such as USART, I²C, and SPI allow easy interfacing with sensors, actuators, displays, and other external devices. DMA support improves data transfer efficiency while minimizing CPU load.

Housed in a TSSOP-20 package, the STM32G030F6P6 is ideal for space-constrained designs, offering a compact footprint while still providing flexible GPIO options with alternate function mapping. Many of its I/O pins are 5-V tolerant, enhancing compatibility with a wide range of external components and legacy systems. On-chip safety features include independent watchdogs and clock security systems for reliable operation.

Supported by the extensive STM32 development ecosystem, including STM32CubeIDE, HAL/LL drivers, and comprehensive documentation, the STM32G030F6P6 is well suited for cost-sensitive consumer electronics, simple industrial controllers, power management circuits, and small IoT nodes, where compact size, reliability, and efficiency are critical.

A-AU/ A-AUR / A-PU/ A-MU / A- MUR
The entire ATMEAG16A Series is available with us at best rates

Digital Signal Processors & Controllers - DSP, DSC 16B MCU DSP 28LD 30MIPS 12KB FLASH

• High current sink/source I/O pins: 25 mA/25 mA• Three 16-bit timers/counters; optionally pair up16-bit timers into 32-bit timer modules• Four 16-bit capture input functions• Two 16-bit compare/PWM output functions- Dual Compare mode available• 3-wire SPI modules (supports 4 Frame modes)• I 2CTM module supports Multi-Master/Slave modeand 7-bit/10-bit addressing• Addressable UART modules with FIFO buffers

The Atmel®AVR® ATmega8A is a low-power CMOS 8-bit microcontroller based on the AVR RISC architecture. Byexecuting powerful instructions in a single clock cycle, the ATmega8A achieves throughputs approaching 1 MIPSper MHz, allowing the system designer to optimize power consumption versus processing speed.

The C8051F020 devices are fully integrated mixed-signal System-on-a-Chip MCUs with 64 digital I/O pins (C8051F020/2) or 32 digital I/O pins (C8051F021/3)
The Entire C8051F020 Series is available with us.
C8051F020-GQ C8051F020DK C8051F020-GQR

The C8051F020/1/2/3 devices are fully integrated mixed-signal System-on-a-Chip MCUs with 64 digital I/O pins (C8051F020/2) or 32 digital I/O pins (C8051F021/3). Highlighted features are listed below; refer to Table1.1 for specific product feature selection.•High-Speed pipelined 8051-compatible CIP-51 microcontroller core (up to 25MIPS)•In-system, full-speed, non-intrusive debug interface (on-chip)•True 12-bit (C8051F020/1) or 10-bit (C8051F022/3) 100ksps 8-channel ADC with PGA and analog multiplexer•True 8-bit ADC 500ksps 8-channel ADC with PGA and analog multiplexer•Two 12-bit DACs with programmable update scheduling•64k bytes of in-system programmable FLASH memory•4352 (4096 + 256) bytes of on-chip RAM•External Data Memory Interface with 64k byte address space•SPI, SMBus/I2C, and (2) UART serial interfaces implemented in hardware•Five general purpose 16-bit Timers•Programmable Counter/Timer Array with five capture/compare modules•On-chip Watchdog Timer, VDD Monitor, and Temperature Sensor

The LPC1768 is a Cortex®-M3 microcontroller for embedded applications with great integration and low power consumption at 100 MHz. Features include 512 kB of flash memory, 64 kB of data memory, Ethernet MAC, USB Device/Host/OTG, 8-channel DMA controller, 4 UARTs, 2 CAN channels, 3 SSP/SPI, 3 I2C, I2S, 8-channel 12-bit ADC, 10-bit DAC, motor control PWM, Quadrature Encoder interface, 4 general purpose timers, 6-output general purpose PWM, ultra-low power Real-Time Clock with separate battery supply, and up to 70 general purpose I/O pins. The LPC1768 shares pins with the 100-pin LPC2368 Arm7TM MCU.

STW9NK95Z is an N-channel power MOSFET designed for high-voltage switching applications. It’s part of ST’s SuperMESH™ series — an optimized evolution of their PowerMESH™ technology that improves conduction performance while retaining rugged switching characteristics. This device is packaged in a TO-247-3 through-hole case, enabling robust thermal management when mounted with an external heatsink.

⚙️ Key Electrical Specifications

• Drain-to-Source Voltage (V_DSS): 950 V — high enough for demanding offline converters, industrial power supplies, and inverters.

• Continuous Drain Current (I_D): 7 A (at case temperature 25 °C) — suitable for medium-power switching applications.

• On-State Resistance (R_DS(on)): ~1.38 Ω @ V_GS = 10 V — this moderate resistance balances efficiency with ruggedness.

• Maximum Gate-Source Voltage (V_GS): ±30 V — the safe drive range for switching operation.

• Gate Threshold Voltage (V_GS(th)): ~4.5 V (max) — typical voltage where the MOSFET begins to turn on.

• Power Dissipation: ~160 W (Tc) — supports significant energy handling with proper cooling.

• Input Capacitance (C_iss): ~2256 pF — relevant for dynamic switching and gate-driver design.

• Gate Charge (Q_g): ~56 nC @ V_GS = 10 V — moderate gate charge that influences switching speed and driver energy.

• Operating Temperature: −55 °C to +150 °C junction — suitable for a broad range of thermal environments.

🧠 Technology & Features

• SuperMESH™ Series: A refined layout that improves R_DS(on) and ensures a very good dv/dt capability, which helps with fast switching transitions in power converters.

• 100% Avalanche Tested: This ensures the MOSFET can tolerate inductive switching spikes and transient voltage stress typically found in high-voltage applications.

• Zener-Protected Gate: Adds ruggedness by protecting the gate from voltage stress and transient conditions.

🧩 Typical Applications

STW9NK95Z is ideal for use in:

• Offline switch-mode power supplies (SMPS)

• DC-DC converters and voltage regulators

• Industrial inverters and motor drives

• Uninterruptible Power Supplies (UPS)

• General high-voltage switching systems

The combination of a 950 V rating, solid current capacity, and balanced switching/thermal performance makes this MOSFET versatile for engineers working on robust power designs where both voltage tolerance and dynamic performance matter.

8-bit Microcontrollers - MCU 14KB Flash 368 RAM 36 I/O
28/40/44 in flashed-based, 8-bit CMOS microcontroller

Using Philips high-density CMOS technology, the Philips is a static 80C51 design with high performance that operates at 5.5 V. The 80C31/32 ROMless devices have an on-chip oscillator and clock circuitry, 8 RAM, 32 I/O lines, three 16-bit counter/timers, a six-source, four-priority level nested interrupt structure, and a serial I/O port for either full duplex UART or multi-processor communications. The gadget also features a wide range of operating frequencies down to zero and a low power static design. There are two software-selectable power reduction modes: idle mode and power-down mode. The CPU is frozen in the idle state, but the RAM, timers, serial port, and interrupt system are still operational. 

The high-performance Arm® Cortex®-M0 32-bit RISC core, operating at a 48 MHz clock, high-speed embedded storage (up to 256 Kbytes of Flash memory and up to 32 Kbytes of SRAM), and a wide variety of improved peripherals and I/Os are all included in the STM32F030R8T6 microcontrollers. All of the devices include common communication interfaces, including one 12-bit ADC, seven general-purpose 16-bit timers, and one advanced-control PWM timer, along with up to two I2Cs, up to two SPIs, and up to six USARTs.

16-bit Microcontrollers - MCU 16b 256KB Flash 96K RAM USB Graphics
The PIC24FJ256DA210 family enhances on the existing line of Microchip‘s 16-bit microcontrollers, adding a new Graphics Controller (GFX) module to interface with a graphical LCD display and also adds large data RAM, up to 96 Kbytes. The PIC24FJ256DA210 family allows the CPU to fetch data directly from an external memory device using the EPMP module

The ATMEGA48PA AU is an 8 bit picoPower AVR RISC based microcontroller with 256 bytes of EEPROM 512 bytes of SRAM 4 kB of ISP flash memory 23 general purpose I O lines 32 general purpose working registers three flexible timer counters with compare modes internal and external interrupts serial programmable USART a byte oriented 2 wire serial interface SPI serial port The gadget can function between 1 8 and 5 5V The device achieves throughputs close to 1 MIPS per MHz while balancing power consumption and processing speed by carrying out strong instructions in a single clock cycle 32 general purpose working registers are combined with a robust instruction set in the AVR core

AMD created the microcontroller Am186ES-40KCW. The Am186 core, which ran at 40 MHz, was included into this MCU. A watchdog timer, a DMA controller, 32 general-purpose I/O lines, and many more capabilities were also integrated on this chip. This chip, like the rest of the Am186ES series, had a hardware handshaking and baud rate generator for the serial port in addition to a larger selection of internal and external interrupt lines.

The 80C51 CMOS single-chip 8-bit microcontroller is available in a high performance CMOS Flash version with a 64 KB flash memory block for code and data storage and a 2048 byte EEPROM for nonvolatile data storage. The ISP capability or software can be used to programming the flash memory in parallel or serial mode. Internally, the normal VCC pin generates the programming voltage.With the addition of a programmable counter array, 1792 bytes of XRAM, a hardware watchdog timer, an SPI interface, a keyboard, a more flexible serial channel that enables multiprocessor communication (EUART), and a speed-up mechanism (X2 Mode), this device has all the features of the Microchip 80C52.

Established in the year 2016 at Mumbai Maharashtra we Adinath Electronics are a Sole Proprietorship based firm engaged as the foremost Wholesale Supplier and Importer of SMD Resistors PCB Connector etc Our products are high in demand due to their premium quality and affordable prices Furthermore we ensure to timely deliver these products to our clients through this we have gained a huge clients base in the market we are importing our products from Taiwan Singapore and Malaysia

Low power, CMOS 8-bit microcontrollers based on the AVR® improved RISC architecture are the ATmega48A/PA/88A/PA/168A/PA/328/P. The devices' ability to process instructions in a single clock cycle results in CPU throughput that is close to one million instructions per second (MIPS) per megahertz. This enables the system designer to balance power use and processing speed.

Ideal for low power (<100nA standby current) and connectivity applications that benefit from the availability of multiple serial ports (3xI2C, 3xSPI), 4xUARTS, and 23 independent timers. Large amounts of RAM (16kB) memory for buffering and large (up to 256kB) Enhanced Flash program memory make it ideal for embedded control and monitoring applications. PPS (peripheral pin select) aids in configuring the most efficient pin configuration of available I/O, and CTMU provides touch support for up to 64 individual buttons. Supports USB 2.0 for device, Host, and OTG with a complete and free software stack that includes a thumb drive application stack. Available in 64, 80, and 100 pin packages.

8-bit Microcontrollers - MCU 64KB 3968 RAM 36 I/O
This family includes long-endurance, Enhanced Flash programme memory in addition to the benefits of all PIC18 microcontrollers, such as great computational performance at a reasonable price.The PIC18F2525/2620/4525/4620 family adds design improvements on top of these features, making these microcontrollers an obvious choice for many high-performance, power-sensitive applications.

We have the below mentioned products in ready stock:
MCP 2554  MCP3201-B I/P  MCP3202-B I/P  MCP3204-B I/P
MCP3208-B I/P 

WE HAVE THE ENTIRE SERIES OF PIC16F72 PIC16F73 PIC16F676  PIC 16F876A  PIC18F452
PIC18F4520 PIC16F877A PIC16F677A PIC18F887A  ETC ...... 

8-bit Microcontrollers - MCU 14KB Flash 368 RAM 36 I/O.
We have all the procucts in this series of microcontroller.

All of the devices in the PIC18F2420/2520/4420/4520family incorporate a range of features that can signifi-cantly reduce power consumption during operation.Key items include:•Alternate Run Modes: By clocking the controller from the Timer1 source or the internal oscillator block, power consumption during code execution can be reduced by as much as 90%.•Multiple Idle Modes: The controller can also run with its CPU core disabled but the peripherals still active. In these states, power consumption can be reduced even further, to as little as 4% of normal operation requirements.•On-the-Fly Mode Switching: The power-managed modes are invoked by user code during operation, allowing the user to incorporate power-saving ideas into their application’s software design.•Low Consumption in Key Modules: The power requirements for both Timer1 and the Watchdog Timer are minimized. See Section 26.0 “Electrical Characteristics”for values

Available in Both SMD & DIP INSTOCK 

This powerful (200 nanosecond instruction execution) yet easy-to-program (only 35 single word instructions) CMOS Flash-based 8-bit microcontroller packs Microchip’s powerful PIC® MCU architecture into a 14-pin package and features 8 channels for the 10-bit Analog-to-Digital (A/D) converter, 1 comparator and 128 bytes of EEPROM data memory. This device is easily adapted for automotive, industrial, appliances and consumer entry-level product applications that require field re-programmability.

The PIC16F873, PIC16F874, PIC16F876 and PIC16F877 are the four covered devices. Devices for the PIC16F876/873 and PIC16F877/874 available in 28-pin and 40-pin packages, respectively. On 28-pin devices, the Parallel Slave Port is not implemented.
Each PIC16F87X device has the ability to access an 8K word block of programme memory continuously. Only 11 bits of address are provided by the CALL and GOTO instructions, allowing branching inside any 2K programme memory page. PCLATH4:3> provides the upper 2 bits of the address when performing a CALL or GOTO instruction. The user must make sure that the page choose bits are set when performing a CALL or GOTO instruction in order for the chosen programme memory page to be addressed. The full 13-bit PC is popped off the stack whenever a return from a CALL instruction (or interrupt) is performed. Therefore, the return instructions do not need the modification of the PCLATH4:3> bits (which POPs the address from the stack)

This data sheet covers PIC16F882/883/884/886/887 devices. Devices for the PIC16F882/883/886 are offered in 28-pin PDIP, SOIC, SSOP, and QFN packages. There are 40-pin PDIP and 44-pin QFN and TQFP packages for the PIC16F884/887.

A 13-bit programme counter is available in the PIC16F882/883/884/886/887 devices, and it may address programme memory spaces of 2K x 14 (0000h-07FFh) for the PIC16F882, 4K x 14 (0000h-0FFFh) for the PIC16F883/PIC16F884, and 8K x 14 (0000h-1FFFh) for the PIC16F886/PIC16F887. The initial 8K x 14 space will wrap around if you access a place that is above these limits. The interrupt vector is located at 0004h, whereas the reset vector is at 0000h.

The AT89C52 is an 8-bit CMOS microprocessor with low power consumption and great performance. It has 8Kbytes of programmable and erasable Flash read-only memory (PEROM). The product is made using high density nonvolatile memory technology from Atmel and is compatible with the 80C51 and 80C52 instruction set and pinout that are accepted throughout the industry. The programme memory may be updated in-system or using a typical nonvolatile memory programmer thanks to the on-chip Flash. The Atmel AT89C52 is a potent microcomputer that offers a highly flexible and affordable solution to many embedded control applications by fusing a flexible 8-bit CPU with Flash on a monolithic chip.

We have the entire ATMEL 1304 IC series availabe with us at best price and in ready stock.

Data can be transferred between memories and peripherals using the highly flexible Direct Memory Access Controller (DMAC), a four channel DMA controller, with little assistance from the CPU. The XMEGA DMAC offloads the CPU by handling simple data copying from one area to another when the CPU is engaged in other activities or low-power sleep modes. The XMEGA DMAC is a strong module for all data-oriented applications, including signal processing and industrial control. Its several addressing modes, flexible channel priority selection, double buffering capabilities, and high block sizes all contribute to its strength.With the use of code samples, this application note explains the XMEGA DMAC's fundamental features so that you may start using it right away. Also included is a C-written driver interface. 

A CMOS 8-bit microprocessor with low power consumption and great performance, the AT89C51 has 4K bytes of Flash PEROM. The product is made with high-density nonvolatile memory technology from Atmel, and its pinout and instruction set are compliant with the industry standard MCS-51. The programme memory may be updated in-system or using a typical nonvolatile memory programmer thanks to the on-chip Flash. The Atmel AT89C51 is a potent microcomputer that offers a highly flexible and affordable solution to many embedded control applications by fusing a flexible 8-bit CPU with Flash on a monolithic chip.

With its strong PIC® (RISC) architecture and its CMOS flash-based design, the PIC16F628A-I/P is a mid-range 8-bit microcontroller from the PIC16 family that is easy to programme (it executes instructions in 200 nanoseconds) and delivers a powerful punch. With basic features including 3.5kB of addressable programme memory, 224bytes of data memory, 16 general-purpose I/O ports, and two comparators, this device offers all the benefits of the well-known mid-range x14 architecture. With a broad operating voltage range of 3 to 5.5V, this device runs at a maximum frequency of 20MHz.

A CMOS microcontroller with an 8-bit flash base is called the PIC16F886-I/SP. Self-programming, an ICD, two comparators, eleven channels of 10-bit analog-to-digital (A/D) conversion, one capture/compare/PWM and one enhanced capture/compare/PWM function, a synchronous serial port that can be set up as either the 2-wire inter-integrated circuit (I²CTM) bus or the 3-wire serial peripheral interface (SPITM), and an enhanced universal asynchronous receiver transmitter (EUSART) are among its features. An analogue input signal can be converted to a 10-bit binary representation of that signal using an analog-to-digital converter (ADC). Analogue inputs are used by this device, and they are multiplexed into a single sample and hold circuit. 

A low power CMOS 8-bit microcontroller built on the AVR improved RISC architecture is the ATMEGA1284P-PU. The ATMEGA1284P-PU delivers throughputs approaching 1MIPS per MHz by executing strong instructions in a single clock cycle, which enables the system designer to balance power consumption vs processing performance.